Categories
- bricks & blocks
- mulch, bark & garden soils
- chemicals
- sand, soil, hot mix & more
- turf, fertilizer & soil additive
- decorative pebbles & aggregrate
- cement, concrete, clay & lime
- oxide, additives & tile glue
- building accessories
- lintels & t-bars
- pavers, sleepers & posts
- render & roofing products
- featured products
- special offers
Prohesive Proset Super is a rigid, high strength adhesive used for bond tiles and pavers over masonry substrates. Prohesive Proset Super can be mixed with SikaCeram® T-Latex admixture for use over framed substrates for improved adhesion and flexibility.
- Fixing tiles by thin bed application.
- Use internally and externally.
- Wall and floor applications.
- Ceramic
- Porcelain
- Quarry
- Terracotta
- Monocottura
- Natural Stone*
- Glass Mosaics*
- Concrete
- Masonry
- Cement mortar beds / screeds
- Sheeted substrates*
- Sika approved waterproof membranes*
Advantages
- High bond strength
- Easy to apply
- Low VOC
- Non slump properties
- Good pot life and open time
Packaging
20 kg bags / 64 bags per pallet
Colour
Available in both White and Off White cements
Chemical Base
Cement, Quartz mineral aggregates, polymers and special additives.
Shelf Life
12 months from date of Manufacture.
Storage Conditions
Store in a dry cool conditions for maximum shelf life (high humidity with reduce shelf life).
Product Declaration
C2TE Class adhesive AS ISO 13007
Tensile Adhesion Strength
Initial tensile |
≥ 1 N/mm² |
After water immersion |
≥ 1 N/mm² |
After heat ageing |
≥ 1 N/mm² |
Slip Resistance
T Class ≤0.5mm AS ISO 13007.2:2010
Mixing Ratio
5.5 - 6 Litres of water per 20 kg bag
Ambient Air Temperature
+5°C Min / +38°C Max
Substrate Temperature
+5°C Min / +35°C Max
Pot Life
3 hours at 23°C & 50% RH
Open Time
30 Minutes at 23°C & 50% RH
Applied Product Ready for Use
USE |
WAIT TIME |
Grouting on walls Grouting on floors |
6-8 hours 20-24 hours |
Light foot traffic Full service |
20-24 hours 5-7 days |
Values determined at laboratory conditions: 23°C & 50% RH.
Higher tempertures will reduce times and lower temperatutres will increase times.
Consumption
Notched Trowel Size |
Approx coverage per bag |
6 mm |
8 m² |
10 mm |
5 - 5.5 m² |
Consumption is always dependant on the substrate surface profile, roughness, and application technique.
MIXING
Pour clean cool water into a mixing container and gradually pour the the Prohesive Proset Super powder into the container and stir with a slow speed mixing drill (approx 500 rpm). Mix for 2-3 minutes to a smooth lump free homogeneous consistency. Allow the product to stand (slake) for 5 minutes then restire for an additional minute. Do not add more water. Restirring the mixture may be required during the adhesives pot life.
APPLICATION
Tiles shall be fixed in accordance to with AS 3958.1-2007.
- Ensure the backs of tiles are clean and free from dust and contaminates.
- Apply the adhesive to the substrate with the appropriate sized notched trowel to acheive coverage requirement on both substrate and the back of the tile. Tiles may require back-buttering to acheive minimum coverage requirements.
- Apply the adhesive with a notched trowel in a single direction. Apply the tile, while pressing into the wet adhesive, break the ridges with the tile to fully bed the tile into the adhesive.
- It is advisable to periodically check the back of the tiles for adhesive coverage requirements as the AS3958.1-2007.
- Only apply as must adhesive that can be covered prior to adhesive skinning. If skinning occurs remove and replace with fresh adhesive.
- Remove any excess adhesive from the face of the tile with a damp sponge and ensure grout joint are of uniform depth.
- Movement, expansion and control joints must be installed as per AS 3958.1-2007.
CLEANING OF TOOLS
Tools and equipement can be cleaned with water while adhesive is still wet.